Interiors & furniture

Will it fit through the door? Furniture route checker

Check whether a sofa or other furniture gets through every doorway, hallway corner and stair landing on the way in, and the best way to carry it.

Free to use & exportNo signupLocal processingImperial & metric

Loading the local tool…

Will your sofa fit through the door?

A sofa fits through a doorway if its depth or its height (with the legs off) is less than the door's clear width, or, failing that, if its diagonal depth is. The doorway is rarely the real problem, though. Most failed deliveries stop at the turn just inside: a hallway corner, a door off a narrow hall or a stair landing. This checker tests every segment of the route you enter, one after another, and tells you where the item gets stuck and by how much.

Enter the item's length, depth and height, the diagonal depth if it is a sofa, then add the route in order: doorways, hallway corners, turns from a hallway through a doorway and stair landings, each with its clear width and headroom. For each segment the tool tries every way of carrying the item (upright, on its back, on end, tipped back arm first, or with its leading end raised into the headroom) and reports the best one, the margin left and, where it is blocked, the shortfall. A drawing shows the tightest moment: the item in the opening, or at the critical angle of the turn.

It is geometry, not a guarantee. The item is treated as a rigid box with a sofa profile at straight doorways, and the people carrying it need room too, so treat a margin under about an inch (25 mm) as a warning rather than a yes.

How to use the will it fit through the door? Furniture route checker

  1. Choose Imperial or Metric. Dimensions switch between inches and millimetres.
  2. Enter Item length (longest side), Item depth and Item height, measured at the widest points including arms and legs.
  3. For a sofa, enter Sofa diagonal depth (0 if not a sofa): lay a straightedge from the top of the back to the front of the arm and measure from the bottom back corner up to it at a right angle. Leave 0 for boxes, beds, cabinets and appliances.
  4. If the legs or feet unscrew, enter their height in Legs that unscrew (height) so the check uses the height without them.
  5. Add one route segment per doorway or turn, in the order the item travels. Pick the Segment type, then enter the Clear width (the door's clear opening, or the hallway you are coming from), the Clear height or headroom and, for turns, the Hallway width (turns only). For a turn through a doorway, the clear width is the door and the hallway width is the corridor in front of it.
  6. Read the verdict, the tightest segment and its margin, the best way to carry the item and the table for every segment, then download the PDF, CSV or SVG drawing to share with the delivery team.

Worked example

Imperial: An 84 × 38 × 34 in sofa with a 30 in diagonal depth clears a 32 in doorway by 2 in, tipped back and carried arm first, then slides round a 42 in hallway corner on end with 4.5 in to spare. Its narrowest straight-through doorway is 30 in.

Metric: A 2,130 × 970 × 860 mm sofa with a 760 mm diagonal depth clears an 813 mm doorway by 53 mm, tipped back and carried arm first, then slides round a 1,070 mm hallway corner on end with 119 mm to spare. Its narrowest straight-through doorway is 760 mm.

How to measure a sofa and the route for delivery

Measure the item at its largest points, not the catalogue's seat or cushion sizes, and measure each opening at its narrowest. A doorway's clear width is the distance from the door stop on the latch side to the face of the door when it stands open at 90°, which is usually about 2 in (50 mm) less than the door's nominal size because the open door and the stop both take up space.

Walk the route from the truck to the room and write down every doorway, corner, landing and low point in order. Note the ceiling height at each turn: it decides whether a long piece can be stood on end or tilted to swing round.

What to measure
MeasurementWhereTip
Item lengthOutside of one arm to outside of the otherFor a sectional, the largest piece that ships alone
Item depthBack of the frame to the front of the arm or seatInclude any rear legs that stick out
Item heightFloor to the top of the backNote how tall the legs are and whether they unscrew
Diagonal depth (sofas)Bottom back corner up to a straightedge laid from the top of the back to the front of the armMeasure at a right angle to the straightedge
Door clear widthDoor stop to the face of the open doorNot the slab or the frame
Hallway widthWall to wall, or wall to the nearest handrail or radiatorMeasure at the turn, where it is often narrower
HeadroomFloor to the lowest point overheadLight fittings, door heads, beams and stair soffits

Standard door, hallway and stair sizes

US residential doors are usually 80 in (6 ft 8 in) high and 24 to 36 in wide in 2 in steps. The 2009 and later editions of the International Residential Code ask for at least one exterior door with a 32 in clear width and a 78 in clear height (R311.2), hallways at least 36 in wide (R311.6) and stairs at least 36 in wide with 6 ft 8 in of headroom (R311.7). Older homes, bedrooms, bathrooms and closets often have narrower doors, and adopted codes and amendments vary, so always measure.

Typical sizes and approximate clear openings
OpeningNominal sizeTypical clear width
Front door (US)36 × 80 inAbout 33–34 in
Interior door (US)32 × 80 inAbout 29–30 in
Bedroom or bathroom door (US)30 × 80 inAbout 28 in
Older or closet door (US)28 × 80 inAbout 26 in
Hallway, IRC minimum36 in wideLess at radiators, trim and handrails
Stair, IRC minimum36 in wide, 6 ft 8 in headroomHandrails may project up to 4½ in each side
UK internal door762 × 1,981 mm (2 ft 6 in × 6 ft 6 in)About 710 mm
Australian internal door820 × 2,040 mmAbout 770 mm

Four ways a sofa gets through a doorway

Movers have four standard moves for a straight doorway, and the calculator tries all of them. Upright, length first: carried as it stands, arm first; needs the depth within the clear width. On its back: needs the height within the clear width, which is why removing the legs often settles it. Arm first, tipped back: the sofa's side profile is rotated in the opening so its narrowest width, the diagonal depth, crosses the door; needs the diagonal depth within the clear width. On end, pivoted through: the sofa is stood on one arm and swung through; needs the length within the door height and the diagonal depth within the clear width.

For boxes, beds, cabinets and appliances the diagonal-depth moves do not apply, but the tool still tries the cross-section at an angle in the opening, which can let a piece taller than the door through when the opening is wide enough.

Checks for an 84 × 38 × 34 in sofa with a 30 in diagonal depth
MoveNeedsThrough a 32 × 80 in clear opening
Upright, length firstDepth 38 in ≤ clear widthNo, 6 in too wide
On its backHeight 34 in ≤ clear widthNo, 2 in too wide
Arm first, tipped backDiagonal depth 30 in ≤ clear widthYes, 2 in to spare
On end, pivoted throughLength 84 in ≤ door heightNo, 4 in too long

How long an item can go round a hallway corner

Turning a corner is the classic moving-furniture problem. An item of plan width w swinging from a corridor a wide into one b wide is tightest partway round, where its outer side touches both outer walls and its inner side brushes the inner corner. The longest item that makes it is the minimum over the angle θ of a/sin θ + b/cos θ − w/(sin θ cos θ). The tool solves this numerically for every orientation and draws the item at that critical angle.

Two things help a lot. Standing the item on end shrinks its plan to its depth and height, as long as the ceiling is taller than its length. And raising the leading end into the headroom shortens the plan length to l cos φ + v sin φ. The table below is for a level item, so a tilted or upended piece can do better.

Longest level item that swings round a right-angled corner, inches
Corridor widths24 in wide item30 in wide item34 in wide item
36 × 36 in53.841.833.8
36 × 42 in62.049.941.7
42 × 42 in70.858.850.8
48 × 48 in87.875.867.8

Worked example: a sofa through the front door and the hall

An 84 × 38 × 34 in sofa with a 30 in diagonal depth arrives at a front door with a 32 in clear width and an 80 in clear height. Upright it is 6 in too deep and on its back 2 in too tall, but tipped back and carried arm first it needs only its 30 in diagonal depth: 2 in to spare. The next segment is a 42 × 42 in hallway corner under a 96 in ceiling. Stood on end, the 84 in length fits under the ceiling and the plan shrinks to 38 × 34 in, which slides round with about 4.5 in to spare. The verdict is that it fits, with the front door as the tightest point.

Add a third segment, a turn from that 36 in hallway into a bedroom door with a 30 in clear width, and the result changes to blocked. Every way of carrying it is at least 34 in wide in plan, wider than the door, and standing it on end needs 84 in of door height where there is 80. The closest attempt is 4 in short, which the calculator reports along with what to try next.

Who it is for and when to use it

Before you order a sofa

Check the size you like against your own doors, hallway and stairs before you pay, and compare models by their margins.

Planning a move

Run the big pieces through the new home's route, decide which need their legs off or a door removed, and send the PDF to the movers.

Delivery teams and retailers

Answer the 'will it fit?' question for a customer with their measurements, and show the carrying method on the drawing.

Renovating a hallway or stair

Test how much a wider door, a moved wall or a bigger landing changes what furniture can reach the rooms beyond.

Method, formulas & assumptions

Straight doorways: for each axis of travel the item's cross-section p × q is rotated in the opening; at angle θ it needs (p cos θ + q sin θ) wide by (p sin θ + q cos θ) high, and the margin is the smaller spare dimension, maximised over θ. Sofas also pass arm first and tipped back when the clear width is at least the diagonal depth and the height at least √(depth² + height²), or on end and pivoted when the length is within the door height. Turns: the longest item of plan width w that swings level from a corridor a wide into one b wide is the minimum over θ of a/sin θ + b/cos θ − w/(sin θ cos θ); an item that is already crosswise slides round without swinging. Raising the leading end by φ shortens the plan to l cos φ + v sin φ while l sin φ + v cos φ stays within the headroom. Every orientation is tried; the margin is how much narrower and lower all clearances at a segment could be.

Imperial inputs are converted with exact factors (1 ft = 0.3048 m, 1 lb = 0.45359237 kg, 1 US gal = 3.785411784 L) before the calculation runs in SI, then results are converted back.

Common mistakes to avoid

  • Measuring the door slab or the frame instead of the clear opening between the stop and the open door.
  • Checking only the front door. The turn into a room or up a stair is usually what blocks a delivery.
  • Leaving out the legs. They often add 4 to 6 in of height that comes off with a few screws.
  • Using the catalogue's seat or cushion dimensions rather than the overall frame size.
  • Forgetting low points: light fittings, door heads, stair soffits and banisters reduce headroom at the turn.
  • Treating a fraction of an inch as a fit. Upholstery compresses, but frames, hands and walls need some room.

Scope & limits

The item is a rigid box; the sofa profile (diagonal depth) is used for straight doorways only. Each segment is checked on its own, assuming room to straighten up between them. A turn through a doorway is modelled as a corridor as wide as the door, which is conservative because a door is only a wall thick. Stair pitch, handrails, banisters, light fittings, door hardware, packaging and the people carrying the item are not modelled; measure the actual clear openings and allow a margin.

Frequently asked questions

Will my couch fit through a 30 inch door?

A 30 in door usually has about 28 in of clear width. A couch goes through if its depth or its height without legs is under that, or if its diagonal depth is. Most full-size sofas are deeper and taller than 28 in, so the diagonal depth usually decides it, and the turn behind the door needs checking too.

What is diagonal depth on a sofa?

Diagonal depth is the narrowest width of the sofa's side profile. Lay a straightedge from the top of the back to the front edge of the arm, then measure from the bottom back corner of the frame up to the straightedge at a right angle. If it is less than the door's clear width, the sofa can usually be tipped back and carried through arm first.

How do I measure a doorway for furniture delivery?

Open the door to 90° and measure from the face of the door to the door stop on the other side; that is the clear width. Measure the clear height from the floor or threshold to the underside of the head. Measure every doorway and turn on the route, not just the front door.

Will a 36 inch deep couch fit through a 32 inch door?

A 32 in door gives about 29 to 30 in of clear width, so a 36 in deep couch will not go through upright. It will go on its back if its height without legs is under the clear width, or tipped back if its diagonal depth is.

How do you get a couch round a tight corner?

Stand it on end if the ceiling is taller than its length, so only its depth and height have to turn, or raise the leading end into the headroom as you swing it. If neither works, take a door off at the turn, try another entrance, or choose a sofa with removable arms or a sectional that ships in pieces.

Does taking a door off its hinges make more room?

Yes. With the door off, the space the open door occupied is freed, usually about the door's thickness, 1⅜ in for an interior door and 1¾ in for an exterior one. Removing the stop moulding adds a little more.

What size couch fits through a standard door?

Through a 36 in front door with about 33 to 34 in clear, most sofas up to about 33 in deep or tall without legs go straight in, and many deeper ones go by diagonal depth. Length rarely matters at a straight doorway, but it decides whether the sofa makes the next turn.

Does it work for beds, fridges and other furniture?

Yes. Leave the diagonal depth at 0 and the item is treated as a box. It tries every orientation and angle at each doorway and turn, so it works for dressers, mattresses, box springs, appliances, pianos and crates.

Do I need an account to download the result?

No. All calculations, local file processing and exports on this page are free, without an account.

Where are my inputs stored?

The tool keeps inputs in this browser tab. It does not upload them or create a cloud copy. Save or download anything you want to keep before leaving the page. Standard site analytics may operate independently of the tool.

Can I work in metric instead of imperial?

Yes. Use the Imperial / Metric switch above the inputs. Imperial (feet, inches, pounds, gallons) is the default; switching converts every dimensional field and result, and your choice is remembered across the free tools in this browser.

Further reading

In this category

Explore the room at eye level before anything is ordered.

Place furniture, fittings and lighting from Harth's object library, walk through the room in 3D and render it for your client, starting from a model you've already drawn. Downloaded results are yours to take with you.